EURO POLYMERS EL-240 / Self Leveling Epoxy Paint

Origin:   VIETNAM

Packing: 24 Kg/Set (Pail A: 20kg, Pail B: 4kg)

EURO POLYMERS EL-240

EL-240 is 2 components, solvent free Epoxy self-levelling to create a 1-3mm thick layer with high adhesion, durability, chemical resistance, abrasion and dust resistance. 

PRODUCT DESCRIPTION

  • EL-240 is a self-levelling finish coating used for indoor concrete/screed floor subjected to medium and high loads such as warehouse, hall, workshop, garage, screed, steel need to be anti-dust, subjected to medium/high loading such as: warehouse, hall, factory, garage, parking areas, basement floors, multipurpose sport center, ...
  • Anti-slip can be applied to wet areas, food processing plants, hangars, ...

* Note: When apply outdoor, discoloration might happen due to epoxy’s characteristic 

FEATURES & BENEFITS 

  • Easy application 
  • Easy cleaning 
  • Good chemical and impact resistance
  • Solvent free
  • Environment friendly
  • Gloss finish, wide range of color for your choice
  • Anti-slip property when needed
  • High flow rate, self-levelling
  • Form a durable cured coating, against solvents, alkalis, oils, greases, salt, wet, ...
  • Can be mixed with selected aggregate to improve bearing load capacity

SURFACE PREPARATION

  • The substrate should be dry, clean and free from laitance, oil, dust, paint residues, algae, loose and friable material must be completely removed from all surfaces before application of the product.

PRIMING

  • Use Euro Polymers EP-200 Primer with consumption 0.15-0.20 kg/m2, leave it dried for 2-4 hours prior application of EC-210

APPLICATION

  • To avoid pinhole due to air bubbles, EP-200 Primer must be applied carefully to ensure all surfaces have fully sealed. It is necessary to apply 2nd coat of EP-200 Primer to high absorbent area(if necessary), and/or time to recoat is longer than 72 hours. The extra priming also request in case of primed area is dusty and cannot clean
  •  Time between coats: 4-8 hours
  • Clean all application tools using Thinner 20 before it cures

CONSUMPTION

  • 1mm thick system:

       EL-240 + Silicat (0.1 ~ 0.3mm) =1.0kg + 0.5kg/m2/mm

  • 1.5-3mm thick system

       EL-240 + Silicat (0.1 ~ 0.3mm) = 1.5kg~3Kg + 0.75kg~1.5Kg/m2/mm

  • 4mm thick, Anti-slip system

      EL-240 + Silicat (0.1 ~ 0.7mm) + EC-210 = 4kg+ 2kg + 0.3kg/m2/mm
The coverage might vary depend on the substrate condition 

 

TECHNICAL DATA

Product type 2 components, solvent free epoxy
Color Grey, Green or upon requested
Waterproof workable
Substrate moisture ≤ 80% RH, test method: moisture meter
Density ~ 1.55 kg/ltr (mixture) 
Solid content ~ 95 ± 3%
Mixing ratio A : B = 5 : 1
Application temperature Air: 5 - 35°C
Surface: < 40°C
Relative humidity: ≤ 80% RH
Dilution Not recommended
Apply method Steel and notch trowels, spike roller
Dry time
(depend on temperature and relative humidity)
30°C, 80% RH
Application time: 20 minutes
Surface dry time: 2 hours
Walkable: 2 days
Lightly receive physical load: 3 days
Fully chemical cured: 7 days
0965.946.943
popup

Qty:

Total: